Shimano TL FC32 Installation Tool 3d models

A printable substitute for the Shimano TL-FC32 Installation Tool. It requires having the TL-FC25 Adapter, which is included with the compatible Shimano BSA bottom brackets. Trying to reduce the need to buy many of the rarely used bike tools... save...

Shimano TL-8S20/TL-AF20 Right Hand Cone Installation Tool for Alfine/Nexus/Inter-8 internal gear hub. This is the counterpart to https://www.thingiverse.com/thing:5646832 which is used to remove the cone. ... The window has been added to be able to see...

This is a Shimano Tool (TL-FH16) to Install the outer seal Ring (Y3FM26000). ...For use with Shimano microspline freehub FH-M8110-BS, to set the correct deep.

SHIMANO TL-EW02 DI2 TOOL FOR E-TUBE CABLE

Shimano pedal tool TL-PD40to be used with a socket wrench 22mm

SHIMANO CRANK INSTALLATION TOOL FOR HOLLOWTECH II

Its a Shimano Crank Installation Tool for HollowTech II

Scaled down version of the TL-FC32. Fits the newer BB-MT800 and other smaller Hollowtech II bottom brackets. Printed with 7 Shells and 50% Infill. ...Works nicely, fit is a bit loose, could be scaled down a bit, maybe 1-2%, but works as-is...

Tool to tighten (or disassemble) shimano pedals like PD-540 SL or PD-5600SL

This tool allows you to adjust the Bottom Bracket axial preload on Shimano Hollowtech II cranksets.

... bolt are hand tight and thus Tool2 is good enough for the job. Tool3 can be printed without any support. Use whichever tool you prefer to tighten the crank arm so that it has no free play yet not so tight that it pressed hard on the bearings.

This tool allows you to adjust the bottom bracket bolt on the non-drive side crank arm of Shimano Hollowtech II cranksets. ...I lost mine, now I can 3d print replacements as needed.

The little cap which this tool loosens and tightens must be torqued to 6-8Nm to move the left crank close enough to the bottom bracket bearings, but not too tight to pinch the bearings. Therefore, per Shimano specs and instructions, the cap must be...

This tool can be used to loosen that Torx-like cap, which is holding the left crankarm on the bottom bracket spindle (see picture). This is needed to swap/clean your crankset or replace the chainrings. The video here explains how to remove your...

This tool can be used to loosen that Torx-like cap, which is holding the left crankarm on the bottom bracket spindle (see picture). This is needed to swap/clean your crankset or replace the chainrings. The video here explains how to remove your...

I added a 1/4 inch square hole in the back of the tool, to be able to use a ratchet and get more leverage when undoing a stuck pre-tensioning cap. ...You don't need extra leverage to tighten the cap, since it only requires 0.7 - 1.5Nm of torque to...

Stronger design with higher wall thickness throughout and reinforcements at the relevant points. ...Fits perfect on my Shimano Steps Lock Ring (Y78N00085, Drive Unit DU-E6100). ...

Shimano Hollowtech II TL-FC16

Shimano sells the TL-PD40 for this purpose, but I don't have a large enough wrench or the appropriate Bottom Bracket tool to turn it with. So I whipped up a version that will fit the BB tool I do own, a Park Tool BBT-9 for my Hollowtech II BB. ...I also...

Shimano pedal service tool TL-PD40-BTL-27L a tool to disassemble the shimano pedal. Similar to the TL-PD40 tool. can be used in combination with a 44 mm bottom bracket tool. ...I use it together with the BBB/BTL-27L.

This is a light wrench to remove cassette gear by mean of a Shimano TL-LR15 tool. Useful in bike travels. Version 2 is a reinforced version, but both are strong enough. ...

This is similar to Shimano's TL-AF10 tool. The tool is a snug fit on the hub, make sure to press it down into the tabs. Shimano says to tighten the dust cap to 5-6 N-m. The dustcap is made of plastic, don't over tighten it. ...The threads on the dust...

Tool for plugging/unplugging SD-EW300 wires for the new Shimano/Dura-Ace 8100/9200 Di2 wires. ... Have tested with EW300 wires (non-I) and seems to work like a charm!

This is a 16-Notch 41mm diameter Shimano bottom bracket installation and removal tool that replaces the Shimano TL-FC24 and TL-FC25 adapters. It works with Shimano BBR60 and BB-MT800 bottom brackets. ...It is to be used with a 1/2" or 12.7mm square...

I needed a tool to drive my Shimano crank bolt with, so I whipped up this simple adapter to convert to a hex driver. ...Fit perfectly on the first try REMIXED added a circle for the holding fingers ( as in the original parts )

If you've dismantled a set of Shimano M324 pedals and found you really don't want to pay for the special tool to hold the outer cone while you tighten the locknut, give this a try. It's designed to fit as snugly as possible round the 13mm head of...

I'm constantly misplacing these 2 tools, so I made a holder with magnets to stick on onto my metal pegboard. I also glued one next to my keyboard in the service area. I have spots for two 3x8mm round magnets. I melted in a chain pin into the...

I remixed this tool to fit my torque wrench. Not many other people will have a wrench that works at 0.5 - 1.5 Nm, but here you go anyway. I also reworked it to print a bit easier, got rid of overhangs and chamfered the finger wheel. ...Enjoy

I took a CAD file of the crank replace tool and used Abaqus to optimise the structure and make it as cheap as possible to print, looks flimsy but is actually very stiff despite being printed on a very cheap 3D printer. ...Total weight is 4.6 g so cost...

Worked like a charm. ... I've printed it with 8 walls andd 100% infill.