Mondlandefähre Apollo 11 STL-OBJ-Dateien für 3D-Drucker

Follow me
FACEBOOK: https://www.facebook.com/groups/1797954133626126/?ref=bookmarks

ISTAGRAM: cody3d1 https://www.instagram.com/cody3d1/

TWITTER: https://twitter.com/Cody3D
ARTSTATION: https://www.artstation.com/cody3d/store
YOUTUBE: https://www.youtube.com/channel/UCegptSyuzQWuU1Fow04_MKw?view_as=subscriber

Lunar Module Apollo 11 STL-OBJ files for 3D printers FDM-FFF DLP-SLA-SLS

Assembly Figure
more than 200 hours of modeling
two versions
however, the dimensions can be changed with each slicer

in total Lunar Module is composed of 5,000 mil points
all the files have been decimated by the polygons, but without losing the details, this makes the light files suitable for each computer

dimensions FDM-FFF W 43 Cm D 43 Cm H 33 Cm

W 17 inch D 17 inch H 13 inch

dimensions DLP-SLA-SLS W 18 Cm D 18 Cm H 13 Cm
W 7 inch D 7 inch H 5 inch

all files are already in place for optimal printing

Lunar Module 3D model was designed to get a clean print result, without considering printing material consumption, However, you are free to rotate, or scale,
every part of the model in the most convenient way for you.
Each file has been checked and repaired with Netfabb
The parts of the model are already positioned for 3D printing
Compatible with every Slicer- Simplify3D, Care, Slic3r, etc ...
All the parts of the model have been cut so as to be printed vertically, for a higher quality of printing

The Apollo Lunar Module (LM /ˈlɛm/), originally designated the Lunar Excursion Module (LEM), was the lunar lander spacecraft that was flown between lunar orbit and the Moon's surface during the United States' Apollo program. It was the first crewed spacecraft to operate exclusively in the airless vacuum of space, and remains the only crewed vehicle to land anywhere beyond Earth.
Structurally and aerodynamically incapable of flight through Earth's atmosphere, the two-stage lunar module was ferried to lunar orbit attached to the Apollo command and service module (CSM), about twice its mass. Its crew of two flew the complete lunar module from lunar orbit to the Moon's surface. During takeoff, the spent descent stage was used as a launch pad for the ascent stage which then flew back to the command module, after which it was also discarded.
Overseen by Grumman, the LM's development was plagued with problems that delayed its first uncrewed flight by about ten months and its first crewed flight by about three months. Still, the LM became the most reliable component of the Apollo–Saturn space vehicle.[1] The total cost of the LM for development and the units produced was $21.3 billion in 2016 dollars, adjusting from a nominal total of $2.2 billion[2] using the NASA New Start Inflation Indices.[3][failed verification]
Ten lunar modules were launched into space. Of these, six were landed by humans on the Moon from 1969 to 1972. The first two flown were tests in low Earth orbit: Apollo 5, without a crew; and Apollo 9 with a crew. A third test flight in low lunar orbit was Apollo 10, a dress rehearsal for the first landing, conducted on Apollo 11. The Apollo 13 lunar module functioned as a lifeboat to provide life support and propulsion to keep the crew alive for the trip home, when their CSM was disabled by an oxygen tank explosion en route to the Moon.
The six landed descent stages remain at their landing sites; their corresponding ascent stages crashed into the Moon following use. One ascent stage (Apollo 10's Snoopy) was discarded in a heliocentric orbit after its descent stage was discarded in lunar orbit. The other three LMs were burned up in the Earth's atmosphere: the four stages of Apollo 5 and Apollo 9 each re-entered separately, while Apollo 13's Aquarius re-entered as a unit.
"wikipedia"

LEGAL PRIVACY POLICY: Any UNAUTHORIZED use of my profile, video, pictures or audio in any form or in a forum now or in the future is NOT permissible without my expressed written consent.
Any act to promote or gain profit in any manner (e.g. either monetarily or socially) from the use of my profile, video, pictures or audio in any form my profile is a violation
of my privacy and subject to legal action. BY WATCHING THIS: You acknowledge and agree that you shall not post, upload, publish, transmit or make available in any way content of this
page including images and recording streamed live video available for download. This is intended as, and presented as a one time, live, one view presentation only.
Penalties of Copyright Infringement: By reproducing, republishing or redistributing the work of a copyright holder without permission, you may be violating or infringing
on his or her rights under the Copyright Act. The copyright holder may sue for compensation cost from $ 250 to $ 150,000 or one year jail sentence

Empfohlene Einstellungen für den Druck

jedes Teil wurde so geschnitten, dass es vertikal gedruckt wird, um eine bessere Druckqualität zu erzielen, also für die oberen Teile,

es wird empfohlen, mit einer 4-5 Schürze zu drucken

Qualität

Schichthöhe: 0,1mm*

Anfangsschichtdicke: 0,3mm

Unteres/oberes Muster: Linien

Horizontale Ausdehnung: 0,04mm (bei Eingabe des Index 0,04mm nimmt der 3D-Drucker das Modell als Monolith wahr, d.h. ohne verdeckte Schichten).

*Schichthöhe 0,1mm wird für eine bessere Qualität des gedruckten Modells empfohlen. Allerdings wird sich die Druckzeit verdoppeln.

Als Anbieter von STL-Dateien ist es unser Ziel, sicherzustellen, dass die Dateien fehlerfrei sind und möglichst genau gedruckt werden können. Deshalb testen wir nur den Druck der schwierigsten Segmente von

Teile des Modells.

Die Teile des Modells wurden getestet und in PLA gedruckt. Falls Sie Ratschläge benötigen, woher Sie Ihre Filamente bekommen können, besuchen Sie die Website unseres Partners.

Geschwindigkeitsaufbauten:

Einfüllgeschwindigkeit: 30mm/s

Geschwindigkeit der Außenhülle: 30mm/s

Geschwindigkeit der Innenschale: 20mm/s

Geschwindigkeit oben/unten: 20mm/s

Geschwindigkeit der Stütze: 50mm/s

Verfahrgeschwindigkeit: 150mm/s

Geschwindigkeit der Schürze: 30mm/s

Anzahl der langsameren Schichten: 4

Füllung:

Muster der Ausfachung: Raster

Linienabstand: 1,5 mm

Überlappung der Füllung: 20%

Füllungsschichten: 0

Stütze:

Aktivieren Sie die Unterstützung: Prüfen Sie

Platzierung: Überall

Überhangwinkel: 30°

X/Y-Abstand: 0,7mm

Oberer Abstand: 0.2mm

Unterer Abstand: 0.2mm

Höhe der Treppenstufe: 0,5mm

Fugenabstand: 0,7mm

Flächenglättung: 0.6mm

Türme verwenden: prüfen

Muster: Raster

Linienabstand: 1,5 mm